Browse Our Catalog

IO Modules - Page 6 - Extreame Savings! Save up to 42%


Extreame Savings! Up to 42% off on IO Modules at Days of Revelation, Page 6. Top brands include ARCELI, kjdElectronics, Electronics-Salon, Opto 22, NIEC, RADWELL VERIFIED SUBSTITUTE, King Pigeon, Advantech, MagnetoSpeed, Siemens, Brentek, Semikron, & ICP DAS. Hurry! Limited time offers. Offers valid only while supplies last.



ARCELI Prototype Screw/Terminal Block Shield Board Kit for Arduino MEGA 2560 R3 DIY Soldered
ARCELI Prototype Screw/Terminal Block Shield Board Kit for Arduino MEGA 2560 R3 DIY Soldered
By ARCELI
In Stock
$19.99

mpn: 00115, ean: 8002124603336,

4.6 out of 5 stars with 31 reviews
PCB:FR-4 fiber glass PCB, dual copper layers, size 120mm x 78mm.Pads grid / pitch 2.54mm / 0.1'', hole diameter 0.8mm.Terminal block pitch 3.5mm / 0.138'', hole diameter 1.2mm.Terminal Block:Pitch 3.5mm / 0.138'' mini terminal blocks, total 84 pins(3pole x24pcs, 2pole x6pcs ).Wire range 26~16AWG, strip length 5mm, screws M2 steel, pin header and cage brass.Female Header Socket:Pitch 0.1''/2.54mm, pin length 15mm / 0.59''Single row 10pin x1pcs, singal row 8pin x 5pcs, dual row 18pin x1pcs.Note: T


5 pcs - MCP23017 - i2c 16 input/output port expander
5 pcs - MCP23017 - i2c 16 input/output port expander
By kjdElectronics
In Stock
$23.95

mpn: 1, ean: 0701017970392,

4.1 out of 5 stars with 56 reviews
16-bit remote bidirectional I/O port - I/O pins default to input - High-speed I2C interface (MCP23017) - 100 kHz - 400 kHz - 1.7 MHz - High-speed SPI interface (MCP23S17) - 10 MHz (max.) - Three hardware address pins to allow up to eight devices on the bus - Configurable interrupt output pins - Configurable as active-high, active-low or open-drain - INTA and INTB can be configured to operate independently or together - Configurable interrupt source - Interrupt-on-change from configured register


Electronics-Salon D-SUB DB37 Male / Female Header Breakout Board, DSUB Terminal Block Connector.
Electronics-Salon D-SUB DB37 Male / Female Header Breakout Board, DSUB Terminal Block Connector.
By Electronics-Salon
In Stock
$17.99
$14.99
You Save: 17%

mpn: MD-D208-1, ean: 6921407426825,

4.1 out of 5 stars with 22 reviews
D-SUB DB37 Male / Female Header Breakout Board. DB37 male and female header connectors. Pitch 3.81mm/0.15'' screw terminal block. FR-4 fiber glass PCB, dual copper layers. Dimensions: 72 x 77.35 x 20mm(W x L x H). 100% new, never used. Rated voltage: 60V. Rated current: 1A / per pin. Operating Temperature: -20ºC to 50ºC Terminal block specifications: Wire range - 26-16AWG. Strip length - 5mm. Screws - M2,steel,Cr3+ Zn plated. Torque - 0.2Nm (1.7Lb-In.). Pin header and Cage - Brass.  D-SUB


Opto 22 SNAP-PAC-RCK4 - SNAP PAC 4-Module Mounting Rack
Opto 22 SNAP-PAC-RCK4 - SNAP PAC 4-Module Mounting Rack
By Opto 22
In Stock
$125.00

mpn: SNAP-PAC-RCK4, ean: 0013227037551,

4.1 out of 5 stars with 36 reviews
The SNAP-PAC-RCK4 mounts one SNAP PAC brain or on-the-rack controller and up to 4 analog, digital, and serial SNAP I/O modules. Together, the rack, I/O, and processor form an I/O unit that provides distributed control in a SNAP PAC System. This I/O unit can also be used for PC-based control or as intelligent remote I/O for an Allen-Bradley MicroLogix, ControlLogix, or CompactLogix PLC system. This rack works with all SNAP I/O modules on the Opto 22 website. Modules can be mixed on the rack and p


New NIEC Power Module PHT2508CF PHT2508CF
New NIEC Power Module PHT2508CF PHT2508CF
By NIEC
In Stock
$94.00

mpn: PHT2508CF,

4.1 out of 5 stars with 20 reviews
New surplus power module.All items New surplus with 30 days money back warranty. Quality control ensures all products in good working condition or a FULL refund. Order confirmation & shipment notification with tracking information by UPS EXPRESS. Competitive pricing. Courteous, knowledgeable and professional sales personnel.


Opto 22 SNAP-IDC5D - SNAP Digital (Discrete) Input Module, 4-Channel, 2.5-28 VDC/VAC
Opto 22 SNAP-IDC5D - SNAP Digital (Discrete) Input Module, 4-Channel, 2.5-28 VDC/VAC
By Opto 22
In Stock
$45.00

mpn: SNAP-IDC5D, ean: 0013227116218,

4.8 out of 5 stars with 41 reviews
The SNAP-IDC5D provides four channels of 2.5-28 VDC or VAC digital (discrete) input. Each channel senses the on/off status for DC or AC voltages from sources such as proximity switches, push buttons, or auxiliary contacts. The module has removable top-mounted connectors for easy access to field wiring, as well as channel-specific LEDs for convenient troubleshooting. Opto 22 SNAP I/O digital input modules are part of the SNAP PAC System. The module mounts on a SNAP PAC mounting rack with a SNAP P


RADWELL VERIFIED SUBSTITUTE 6ES7-222-1HF22-0XA0-SUB Replacement of Siemens 6ES7222-1HF22-0XA0, Digital Out 8DO X RELAY6ES72221HF220XA0SUB
RADWELL VERIFIED SUBSTITUTE 6ES7-222-1HF22-0XA0-SUB Replacement of Siemens 6ES7222-1HF22-0XA0, Digital Out 8DO X RELAY6ES72221HF220XA0SUB
By RADWELL VERIFIED SUBSTITUTE
In Stock
$110.00

mpn: 6ES7-222-1HF22-0XA0-SUB,

4.7 out of 5 stars with 23 reviews
DIGITAL OUT 8DO X RELAY6ES72221HF220XA0SUB. REPLACEMENT OF SIEMENS 6ES7222-1HF22-0XA0. PLC Module/Rack. PLCs/Machine Control.


Modbus RTU Digital inputs Module 4 Channel IO Ports Compatible NC/NO/Pulse Counter/TTL with RS485 Port
Modbus RTU Digital inputs Module 4 Channel IO Ports Compatible NC/NO/Pulse Counter/TTL with RS485 Port
By King Pigeon
In Stock
$48.00

mpn: DAM108,

4.6 out of 5 stars with 54 reviews
The DAM108 is for monitoring 4 digital inputs(Dry Contact or Wet Contact, counter). It supports Modbus RTU Protocol over RS485 serial port.Powered up by 9~36VDC. It is used widely in industrial automation control systems. E.g.: Base Transceiver Station, diesel generator rooms, engine room, transformer substations, telecommunication equipment rooms, power supply systems and so on. It is an industrial class, high reliability, low-power consumption, high stability and high precision data acquisitio


Advantech ADAM-6015-DE, 7 Channel Isolated RTD Input Module, Modbus TCP Module, ADAM-6015-DE, Replacement of ADAM-6015-BE. Ethernet I/O Module.
Advantech ADAM-6015-DE, 7 Channel Isolated RTD Input Module, Modbus TCP Module, ADAM-6015-DE, Replacement of ADAM-6015-BE. Ethernet I/O Module.
By Advantech
In Stock
$439.99

mpn: ADAM-6015-DE, ean: 0734038852941,

4.5 out of 5 stars with 10 reviews
Advantech, 7 Channel Isolated RTD Input Module TCP Module,, ADAM-6015-DE (REPLACEMENT of ADAM-6015-BE).


MagnetoSpeed M-Series MiniLIGHT Module with Picatinny Rail Adapter, Black
MagnetoSpeed M-Series MiniLIGHT Module with Picatinny Rail Adapter, Black
By MagnetoSpeed
In Stock
$79.99

mpn: MS_MSG_ML, ean: 0855036004122,

4.4 out of 5 stars with 57 reviews
CREE XM-L2 U3 LED for 150 Lm output continuous and over 300 Lm in a momentary ''Overdrive'' modeLight output remains constant till battery depletedIntuitive operation with two button interfaceSeparate circuit for red leds for redundancyAble to tailstand for area illuminationHigh-efficiency electronics for extended runtime using current-control for the lightExtremely low standby current drainRandom strobe, SOS, and beacon outputsCREE XM-L2 U3 LED for 150 Lm output continuous and over 300 Lm in a


Opto 22 SNAP-ODC5R - SNAP Reed Relay Digital (Discrete) Output Module, 4 Isolated Channels, Normally Open, 300 VAC
Opto 22 SNAP-ODC5R - SNAP Reed Relay Digital (Discrete) Output Module, 4 Isolated Channels, Normally Open, 300 VAC
By Opto 22
In Stock
$48.00
$31.04
You Save: 35%

mpn: SNAP-ODC5R,

4.4 out of 5 stars with 37 reviews
The SNAP-ODC5R is a digital (discrete) output module that uses reed relays and does not provide optical isolation. Current rating depends on the voltage the module is used with. This module is normally open. This module was designed for a low-voltage DC load that that is purely resistive (no inrush current). IMPORTANT: Because of its low 10 VA rating, this module cannot be used with inductive or capacitive loads (even very small loads) nor 120 VAC. Part of the SNAP PAC System, these modules moun


Siemens Simatic DP Electronic Module 6ES7 131-4BF00-0AA0
Siemens Simatic DP Electronic Module 6ES7 131-4BF00-0AA0
By Siemens
In Stock
$67.00

mpn: TM-15S24-01,

4.9 out of 5 stars with 31 reviews
Siemens Simatic DP Electronic Module 6ES7 131-4BF00-0AA0.


Watchdog Timer - Brentek G-WDT5 - 2 second Fixed Timeout, Opto 22 G4 Case Size
Watchdog Timer - Brentek G-WDT5 - 2 second Fixed Timeout, Opto 22 G4 Case Size
By Brentek
In Stock
$63.50

mpn: G-WDT5,

4.5 out of 5 stars with 22 reviews
Brentek's G-WDT5 Watchdog Timer Module monitors a control system's activity by detecting on/off transitions of a control line. During normal system operation, the watchdog's internal timer is continually reset by control line activity and its dry-contact output remains energized. When control is lost (control line stops toggling), the timer times-out and de-energizes the output contact, indicating ''Loss of Control''. Loss of Control is caused by problems such as CPU latch-up, control system fau


Opto 22 G4IDC5MA G4 DC Input with Manual/Auto Switch, 10-32 VDC, 5 VDC Logic, 4000 Volt I/O Isolation, 5ms Turn-On/Off Time, 25 Input Current
Opto 22 G4IDC5MA G4 DC Input with Manual/Auto Switch, 10-32 VDC, 5 VDC Logic, 4000 Volt I/O Isolation, 5ms Turn-On/Off Time, 25 Input Current
By Opto 22
In Stock
$49.60
$47.00
You Save: 5%

mpn: G4IDC5MA,

4.3 out of 5 stars with 13 reviews
Opto 22's G4 DC input modules are used to detect on/off DC voltage levels. Each module provides up to 4000 volts (transient) of optical isolation between field inputs and the logic output of the circuit. Typical applications for DC input modules include sensing the presence or absence of voltage and sensing contact closure from sources such as proximity switches, limit switches, selector switches, push buttons, photoelectric switches, and TTL-compatible devices. This module is designed with filt


Opto 22 G4OAC5MA G4 AC Output with Manual/Auto Switch, 12-140 VAC, 5 VDC Logic, 4000 Volts I/O Isolation, 12 mA Logic Input Current
Opto 22 G4OAC5MA G4 AC Output with Manual/Auto Switch, 12-140 VAC, 5 VDC Logic, 4000 Volts I/O Isolation, 12 mA Logic Input Current
By Opto 22
In Stock
$35.09

mpn: G4OAC5MA,

4.4 out of 5 stars with 8 reviews
Opto 22’s G4 AC output modules are used to control or switch AC loads. Each module provides up to 4,000 Vrms of optical-isolation between field outputs and the control side of the circuit, and each features zero voltage turn-on and zero current turn-off. All AC output modules are equivalent to single-pole, single-throw, normally open contacts (Form A, SPST-NO) except the G4OAC5A5, which is equivalent to a single-pole, single-throw, normally closed contact (Form B, SPST-NC). The G4OAC5MA and th


RADWELL VERIFIED SUBSTITUTE 6ES7-235-0KD22-0XA0-SUB Replacement of Siemens 6ES7235-0KD22-0XA0, I/O Module
RADWELL VERIFIED SUBSTITUTE 6ES7-235-0KD22-0XA0-SUB Replacement of Siemens 6ES7235-0KD22-0XA0, I/O Module
By RADWELL VERIFIED SUBSTITUTE
In Stock
$210.00

mpn: 6ES7-235-0KD22-0XA0-SUB,

4.8 out of 5 stars with 44 reviews
I/O MODULE. REPLACEMENT OF SIEMENS 6ES7235-0KD22-0XA0. PLC Module/Rack. PLCs/Machine Control.


Advantech ADAM-6051-D 14-ch Isolated Digital I/O Modbus TCP Module with 2-ch Counter - 1 x Network (RJ-45) - Fast Ethernet - 10/100Base-TX (Replacement of ADAM-6051-BE ADAM-6051-A)
Advantech ADAM-6051-D 14-ch Isolated Digital I/O Modbus TCP Module with 2-ch Counter - 1 x Network (RJ-45) - Fast Ethernet - 10/100Base-TX (Replacement of ADAM-6051-BE ADAM-6051-A)
By Advantech
In Stock
$217.00

mpn: ADAM-6051-D, ean: 0767870671890,

4.7 out of 5 stars with 7 reviews
Advantech ADAM-6051-D 14-ch Isolated Digital I/O Modbus TCP Module with 2-ch Counter - 1 x Network (RJ-45) - Fast Ethernet - 10/100Base-TX (Replacement of ADAM-6051-BE ADAM-6051-A)ADAM-6000 accomplishes the integration of automation and enterprise systems easily through internet.


Semikron SEMiX553GB128Ds Igbt Semikron Module Original
Semikron SEMiX553GB128Ds Igbt Semikron Module Original
By Semikron
In Stock
$176.70

mpn: iX553GB128Ds,

4.4 out of 5 stars with 32 reviews
.


ICP DAS USA ICP-tGW-715 Tiny Modbus TCP to Modbus RTU / ASCII PoE Gateway, with 1 RS-422/RS-485 port.
ICP DAS USA ICP-tGW-715 Tiny Modbus TCP to Modbus RTU / ASCII PoE Gateway, with 1 RS-422/RS-485 port.
By ICP DAS
In Stock
$159.00

mpn: tGW-715,

4.4 out of 5 stars with 58 reviews
The tGW-715 is a tiny Modbus TCP to Modbus RTU/ASCII gateway that enables a Modbus TCP master to communicate with Modbus RTU/ASCII serial devices through Ethernet network, which eliminates the cable length limitation of serial devices. The tGW-715 tiny Modbus TCP to Modbus RTU/ASCII gateway can be used to create a pair-connection application, serial-bridge or serial-tunnel application. It can route data over TCP/IP between two Modbus RTU/ASCII serial devices, which is useful when connecting main


Opto 22 SNAP-IDC5 - SNAP Digital (Discrete) Input Module, 4-Channel, 10-32 VAC/VDC
Opto 22 SNAP-IDC5 - SNAP Digital (Discrete) Input Module, 4-Channel, 10-32 VAC/VDC
By Opto 22
In Stock
$49.25
$28.74
You Save: 42%

mpn: SNAP-IDC5,

4.2 out of 5 stars with 19 reviews
The SNAP-IDC5 provides four channels of 10-32 volts DC or AC digital (discrete) input. Each channel senses the on/off status for DC voltages from sources such as proximity switches, push buttons, or auxiliary contacts. The module has removable top-mounted connectors for easy access to field wiring, as well as channel-specific LEDs for convenient troubleshooting. Opto 22 SNAP I/O digital input modules are part of the SNAP PAC System. The module mounts on a SNAP PAC mounting rack with a SNAP PAC r



Viewing Page 6 of 7

View more products in Controls & Indicators.
Feel free to Browse Our Catalog.



Privacy Policy / Terms of Service / Accessibility Statement
© 2019 - daysofrevelation.com. All Rights Reserved.